Ultrasonics – Implosion

In the blog Cavitation 101, cavitation in liquids was described as the backbone of ultrasonic cleaning.  Cavitation by itself, however, is not the end of the story.  Although cavitation is the backbone, the real work is accomplished by the implosion of cavitation bubbles.

Cavitation bubbles are, in essence, pockets of vacuum or vapor of the surrounding liquid that are supported ONLY by the negative pressure or rarefaction of the sound wave surrounding them.  Since sound waves travel through the liquid, an area of rarefaction is replaced with a area of pressure or compression as the sound wave moves on.  The cavitation bubble, in some cases, may collapse after a single cycle while in others the cavitation bubble, subjected to alternating compression and rarefaction, starts to oscillate in resonance with the sound wave and grows larger with each passing sound wave until it finally becomes large enough to be unstable.  In the blog What is Resonance?, the phenomenon of resonance growing over many sound wave cycles was described.  In any event, when the cavitation finally does reach a condition of instability (over a single or many sound wave cycles) the result is a violent collapse or “implosion.”  It is the implosion of cavitation bubbles that accomplishes ultrasonic cleaning.

Whan a cavitation bubble implodes, the inward rush of the bubble upon itself driven by the surrounding compression region of the sound wave results in a “collision” of sorts as the energy of the collapse is concentrated to a very small area.  The resulting pressure at the center of the collapse has been estimated to exceed 10,000 PSI (Pounds per Sqauare Inch) and may achieve temperatures exceeding 10,000° Fahrenheit.  Similar conditions exist on the surface of the Sun!  Although the above may seem scary, the high temperature and pressure exist for only an instant and are localized in a very small area at the focus of the implosion.

Illustration of Cavitation Bubble Collapsing

The above is a classic photo of a cavitation bubble collapsing or imploding. Notice that the bubble is collapsing inward and toward the bottom of the picture.

The energy of the collapsing cavitation bubble is often directed toward a nearby solid object which, fortunately for ultrasonic cleaning, is usually the object being cleaned.

There is a lot more to know about cavitation and implosion including what makes it work and what is likely to make it not work.  These topics will be covered in some detail in upcoming blogs.

For those with additional interest, the PowerPoint animation imbedded below

Ultrasonic Cavitation and Implosion Power Point Show

shows how a cavitation bubble is created and implodes under the influence of passing sound waves.  For best results, “save” the presentation on your desktop and then run it as a Power Point show.  There are prompts at the bottom right of the screen to start the motion.  If anyone has difficulty downloading or playing this Power Point, please contact me, jfuchs@ctgclean.com, and I’ll either email it to you or call you to see if we can get it to work.  It is important for me to know if this method of presenting is going to work as many upcoming concepts will be illustrated with similar Power Point animations.

Also, please feel free to email me at the above address with any questions you may have about cleaning using ultrasonics or any of the other Cleaning Technology Group cleaning technologies.  I will attempt to answer your question either in the blog or by return email.

–  FJF  –

All content is © Cleaning Technologies Group except for that specifically attributed to other sources.
Content may be used for purposes not detrimental to the interests of Cleaning Technologies Group when proper credit is given to the source.
This entry was posted in Sound, Ultrasonics, Useful Information Miscellaneous. Bookmark the permalink.

2 Responses to Ultrasonics – Implosion

  1. Sanjay says:

    Mr. Sharkey I fully agree that rinsing is an aslubotely necessary part of the overall cleaning process. In general, it is recommended that a higher ultrasonic frequency be used for rinsing than that used for the preceeding cleaning process. The logic is that the higher frequency will provide better penetration. Remember, rinsing is really just another cleaning step in which remaining residues from cleaning are diluted or dissolved. As far as the frequency for bath changeout, that’s a tough call. Any general recommendation I would give here could be easily disputed. The only way to really know how frequently to replace a rinse requires some full scale laboratory or on-site testing. I suggest you return to the blog home page and enter rinse or rinsing in the search box. Several good references will pop up. I will also make a note to further address rinsing issues in upcoming blogs. Thanks for your question. FJF

  2. Sonny says:

    I found the info on this blog valuable.

Leave a Reply